Lesson 7 (CC2 level)

Not to be confused with Lesson 7.

Lesson 7

Level set	Chip's Challenge 2
Level number	71
Designer	Chuck Sommerville
Password
Password notes
Hint	(See "Hints" section)
Chips	0 required / 0 available
Chips notes
Time limit	0
MS (Scores)
Melinda time	[]
Bold time	[]
Public time	[]
Casual difficulty	*****
Bold execution difficulty	*****
Bold routing difficulty	*****
Bold luck difficulty	*****
Mouse Required	Note: This level's bold route requires use of the mouse.
Lynx (Scores)
Melinda time	[]
Bold time	[]
Public time	[]
Casual difficulty	*****
Bold execution difficulty	*****
Bold routing difficulty	*****
Bold luck difficulty	*****
Steam (Scores)
Bold time	0
Bold time	0
Public time	0
Public time	0
Casual difficulty	*****
Bold execution difficulty	*****
Bold routing difficulty	*****
Bold luck difficulty	*****
Bold score	35500
Public score	35500
Casual difficulty	*****
Bold execution difficulty	*****
Bold routing difficulty	*****
Bold luck difficulty	*****

Lesson 7 is the 71st level in Chip's Challenge 2. It is also the last lesson level. It was created by Chuck Sommerville.

Full level map

Hints

• Be sure to read all the clues carefully. This may seem easy, but it gets complicated.
• This is an 'and' gate. Both of its inputs must be on for its output to be on.
• This button controls one of the inputs to the 'and' gate. It needs to be pressed to be on.
• This door is connected to the output of the 'and' gate. It will open when its input is on.
• Push the blocks onto the two buttons.
• This is an inverter. When its input is on, its output is off. When its input if off, its output is on.
• This black button controls the input to the inverter. It is normally on. It needs to be pressed to be off.
• This door is connected to the output of the inverter. It will open when its input is on.
• Push the block onto the button.
• This is an 'or' gate. When either of its inputs is on, its output is on.
• This button controls one of the inputs to the 'or' gate. It needs to be pressed to be on.
• This door is connected to the output of the 'or' gate. It will open when its input is on.
• Push the block onto one of the buttons.
• This is a 'nand' gate. 'nand' stands for 'not and'.
• This button controls one of the inputs to the 'nand' gate. It needs to be pressed to be on.
• Both of its inputs must be on for its output to be off.
• This door is connected to the output of the 'nand' gate. It will open when its input is off.
• Push the blocks onto the two buttons.
• This is the 'xor' gate. xor stands for exclusive-or.
• Its output is on when one and only one of its inputs is on.
• This is one of the inputs to the 'xor' gate.
• This door is connected to the output of the 'xor' gate. It will open when its input is off.
• Either push the top block off or push the bottom block on.
• This is the 'latch' gate. It has a capture input, a data input, and an output.
• This is the capture input to the latch.
• When it is on the output will be the same as the data on the other input.
• When it is off, the output stays the same as it was the last time the capture was on.
• This is the data input to the latch gate.
• The state of this input is captured by the capture input above.
• This door is connected to the output of the 'latch' gate. It will open when its input is on.
• Push the block onto the bottom button, then step on the top button.
• This is a counter gate. It is using its increment input and its overflow output.
• This is the increment input to the counter gate.
• When its input goes from off to on, it will count up by one.
• When the counter goes from 9 to 0, it will send a quick pulse out the overflow output. A pulse is a short 'on' signal.
• This door is connected to the overflow output of the counter. It toggles when its input goes from off to on.
• Step on the button until the number says 0.
• This counter gate is using its decrement input, and its underflow output.
• This is the decrement input to the counter.
• When it goes from off to on, the counter will count down by one.
• This door is connected to the underflow output of the counter.
• When the counter reaches 9, the underflow output will turn on and open this door.
• Step on the button until the number says 9.

Previous Level	Current Level	Next Level
← Rail Bowling	Lesson 7 (CC2 level)	On and Off →